Talk to a local mold specialist (816) 555-0142

Basement Mold

Basement Mold in Kansas City Homes

Most basement mold in the metro comes down to water pressing on the foundation from outside, or humid air condensing on cold surfaces inside.

If you own a house in the Kansas City area with a basement, you probably have a story about it: the musty smell in July, the damp corner that appears after a heavy rain, the finished room that no one uses anymore. Basements are the most common place for mold in homes here, and also one of the most fixable, once you understand where the water is coming from.

This page is about the local reasons basements get damp, how to tell which kind of water problem you have, what to do about it, and when mold in a basement calls for a specialist.

Why the ground around Kansas City holds water against your house

A large part of the metro sits on clay-rich soil. Clay swells when it is wet and shrinks when it is dry. That has two effects on a basement.

First, wet clay does not drain well. After a hard rain or a wet spring, water stays in the soil around the foundation. The soil gets saturated, and the water presses against the wall and up from under the floor. Engineers call this hydrostatic pressure. Water finds the weak points: the joint where the floor meets the wall (the cove joint), cracks, the holes where utilities pass through, and mortar joints in block or stone walls.

Second, the swell and shrink cycle moves the soil, and the soil moves the foundation a little. Over years, that opens hairline cracks and gaps. A basement that was dry for 20 years may start seeping after a few wet seasons or after a gutter or grading change.

Add humid summers, and a second path opens. Warm, moist air comes into a cool basement, touches a cold concrete wall or a cold water pipe, and drops its moisture as condensation. The wall looks wet, but nothing is leaking. This is common on the north and east sides and in basements with no dehumidifier.

Telling seepage from condensation from leaks

The fix depends on the source. A few simple checks tell you a lot.

The foil test for condensation. Tape a 12 inch square of aluminum foil to a bare wall or floor, sealing all edges, and leave it for a day or two. If moisture shows on the room side of the foil, it is condensation from indoor air. If it is on the wall side, water is coming through the wall or floor.

Where and when it shows up. Dampness that appears within a day or two of rain, along the bottom of the wall, points to seepage or poor drainage outside. Dampness that is worst in July and August and dry in winter points to humidity. A wet spot that appears with no connection to weather may be a plumbing leak from pipes above, a water heater, a washing machine hose or a drain line.

White crust on concrete or block. That is efflorescence, a mineral deposit left when water moves through masonry and evaporates. It is not mold, but it tells you water is moving through the wall.

Stains and smell. Water stains on the lower wall, a tide line, or peeling paint point to repeated wetting. A musty smell with no visible growth often means mold in a spot you cannot see: behind a wall, under carpet, in a closet.

Outside fixes first

Most basement water problems start outside, and fixing them is often cheaper than anything done inside.

  • Gutters and downspouts. Clogged or undersized gutters overflow along the foundation. Downspouts should carry water at least several feet away from the house, not drop it at the wall.
  • Grading. The ground should slope away from the foundation. Settled soil, a flower bed that holds water, or a patio that slopes toward the house will funnel water to the wall.
  • Window wells. Make sure covers are in place and drains are clear. Wells that fill with water leak into the basement.
  • Sprinklers. Heads that spray the foundation, and irrigation leaks, put water exactly where you do not want it.
  • Trees and landscape edging. Roots can disturb drains and crack walls, and heavy mulch can hold moisture against siding.

Do these before paying for interior waterproofing. Many dry-basement problems are solved with a few hundred dollars of gutter and grading work.

Inside: sump pumps and drainage

Houses in the metro often have a sump pit with a pump that moves water out before it rises to the floor. A pump is a mechanical device, and it fails, often during the storm that most needs it. Check:

  • Does the pit have water in it, and does the pump turn on when you lift the float?
  • Does the discharge pipe carry water away from the house?
  • Is there a battery backup? A power outage often arrives with a storm.
  • Is the pit lid sealed? An open pit adds humidity to the air.

If you have no sump and have recurring seepage, a contractor can discuss interior drain tile and a pit, or exterior drainage. These can run into the thousands. Get more than one opinion and ask for a clear explanation of why the system suits your wall and floor.

Interior sealers and paints sold as waterproofing can hide a problem and trap moisture behind them. They have a place on a dry wall, and little place on a wall that is actively seeping.

Dehumidifiers and humidity control

A basement should stay below about 50 to 60 percent relative humidity in summer to discourage growth. In the Kansas City climate, many basements go over that without help.

A good dehumidifier, sized for the space and set to drain to a floor drain or a pump rather than a bucket, is one of the best investments a homeowner can make. Practical tips:

  • Buy a unit rated for the square footage and dampness of your basement. An undersized unit runs constantly and does not keep up.
  • Plumb the drain, or use a condensate pump, so it does not need emptying.
  • Keep it away from walls so air can move.
  • Use a separate hygrometer to check actual humidity, and watch the readings through July and August.
  • Check and clean the filter and coils.

A dehumidifier controls humidity. It does not fix a leak. If water is coming through the wall, the machine will run all day and the wall will stay wet.

Finished basements: where mold hides

Finishing a basement adds living space and also hides problems. Drywall, carpet, wood framing and insulation can all feed mold, and they cover the wall where moisture shows up.

Common trouble spots in finished basements:

  • The bottom of drywall. Wicks water from the floor. Look for staining, soft spots and baseboards that are loose or discolored.
  • Behind built-in cabinets and under stairs. Poor airflow and little chance of anyone noticing.
  • Carpet and pad over a slab. Moisture comes up through concrete, and carpet holds it.
  • Closets on exterior walls. Cold, still air with stored cardboard boxes and fabric is a good place for growth.
  • Bathrooms with no fan or a fan vented into the ceiling.
  • Insulation against block walls. Fiberglass held against a cold wall can collect condensation, and the paper facing is food.

If you smell mold in a finished basement and cannot see it, the source may be inside the wall. A moisture meter and, if needed, a small opening will show whether it is there. See the mold inspection page.

Flooding and water events

The metro has a long history of water. Older neighborhoods near the Blue River, Brush Creek, Indian Creek and Turkey Creek have seen basement flooding in heavy rain, and low-lying areas near the Missouri and Kansas rivers have a longer history still. Sewer backups in older city lines also happen.

After any flood or sewer backup, the clock matters. Materials that stay wet for more than a day or two can grow mold. Wet drywall, carpet and padding usually need to come out. If the water was from a sewer backup or an outdoor flood, it is considered contaminated, and cleanup is different from a clean-water leak. Do not take shortcuts. A specialist can advise on what can be dried and what must be removed.

When basement mold calls for a specialist

You can handle a small patch on a hard surface yourself, once the cause is fixed. The removal page covers the roughly 10 square foot guideline. Call a specialist when:

  • Mold covers more than about 10 square feet.
  • It is on drywall, insulation, carpet or in walls and ceilings.
  • The smell is strong and you cannot find the source.
  • There was flooding, sewage or a long-term leak.
  • Someone in the home has asthma, allergies or a weakened immune system.
  • Your home was built before about 1980 and removal would disturb plaster, flooring or insulation that may contain asbestos, or paint that may contain lead. Those are regulated separately in Missouri and Kansas and affect how the work is done.

What the specialist does is set up containment, run filtered air machines, remove materials that cannot be saved, clean framing and concrete, dry the space and verify the result, as described on the mold removal and remediation page. A good plan also includes a fix for the water source, with the plumber, landscaper or waterproofing contractor named, and a plan for humidity.

What basement jobs may cost

Basement remediation varies with size, finishes and access. A small, contained area might cost several hundred dollars, and a finished basement with drywall, insulation and carpet removed typically runs into thousands. Drainage and waterproofing work is separate and can be a larger number. The specialist quotes after seeing the space. These are general ranges and not this site's prices.

What to do this week

If you suspect a basement mold problem:

  1. Look at the bottom of walls, behind furniture, in corners and closets.
  2. Run the foil test and put a hygrometer in the room.
  3. Check gutters, downspouts, grading and the sump pump.
  4. Move stored items off the floor and away from walls.
  5. If there is visible mold over a larger area, or a smell you cannot trace, call.

You can reach a specialist by calling the number at the top of the page or by using the contact page. For general information, EPA has a free guide to mold and moisture in the home at epa.gov/mold.

How it works

What happens when you call

  1. 1

    Call

    Say what you see or smell, where it is, how long it has been there and whether there was a leak. Renting, buying or owning all change the next step.

  2. 2

    Find the water

    The specialist looks for the moisture source with a meter and a careful visual check, because mold comes back if the water does.

  3. 3

    Test only if it helps

    A lab test when it answers a real question (hidden mold, a home sale, clearance after work). Not when the mold is already visible.

  4. 4

    Plan and quote

    You hear what needs removing, how the area will be contained and what it costs before any work starts.

FAQ

Basement Mold questions

Why is my Kansas City basement musty even when it looks dry?

Humidity is a common cause. Summer air carries moisture into a cool basement, and it condenses on cold surfaces or soaks into stored boxes and carpet. A hygrometer will tell you if humidity is above the 50 to 60 percent range, and a dehumidifier often solves it.

Is white powder on my basement wall mold?

Often it is efflorescence, a mineral deposit left behind when water passes through concrete or block. It is not mold, but it means water is moving through the wall, which is the condition mold needs. Look for the water source.

Do I need to remove drywall if mold is only on the surface?

It depends on how long it was wet and how far growth goes. Surface mold on painted drywall that dried quickly may clean up. Drywall that stayed wet, feels soft or has growth on the back is generally removed.

Will a dehumidifier get rid of mold?

It helps prevent growth by lowering humidity, but it does not remove mold that is already there, and it does not fix leaks.

Should I seal basement walls with waterproof paint?

On a dry wall, maybe. On a wall that seeps, sealers can trap moisture and fail. Fix the drainage outside and inside first, then decide on finishes.

Service area

Serving the Kansas City metro

Mold inspection, testing and removal on both sides of State Line Road, in Jackson, Clay, Platte and Johnson counties.

See all service areas

Basement Mold: call (816) 555-0142

One call connects you with an independent local mold specialist serving both sides of the state line.

Call nowSend a message