People use "mold removal" and "mold remediation" to mean the same thing, and for most homeowners they are. A small difference is worth knowing, though. Removal suggests taking the mold away. Remediation, the word used in the industry standards, means returning the space to a normal condition, which includes finding and fixing the moisture that caused the growth. Mold that comes back in six months was removed, not remediated.
This page walks through the steps of a proper job, what it takes to do each one, what you can safely do yourself, and what to look for in a written scope.
Can you kill mold, and should you try?
Mold that has grown on a material is not solved by spraying something on it. Killing mold with bleach or a fogger leaves dead spores and fragments behind, and those can still bother people who are sensitive. EPA does not recommend routine biocide use. The goal is to physically remove the growth and the material it has taken over, and then dry everything.
Bleach in particular has limits. It does not soak into porous materials such as drywall or wood, so it may whiten the surface while the roots stay. It also releases fumes and can react badly with ammonia and other cleaners. Detergent and water, with a scrub brush and a rinse, is the usual advice for hard surfaces.
The steps of a proper remediation
Step 1: Fix the water first
Nothing else works until the moisture source is stopped. That could be a leaking pipe, a failed seal around a window, a roof leak, a bathroom fan that vents into the attic, a downspout that ends against the foundation, or a sump pump that has stopped working. A remediation company that begins cleanup without naming the source is guessing.
Fixing the source may be a plumber's, roofer's or landscaper's job, not the mold specialist's. Good companies coordinate or at least tell you what needs fixing and why.
Step 2: Set up containment
Cleaning mold stirs it up. Spores and dust become airborne, and without containment they travel through the house and settle in rooms that were clean.
Containment usually means heavy plastic sheeting taped to the ceiling, floor and walls to seal off the work area, with a zippered door and sometimes an airlock chamber. For small jobs it may be a simple barrier around one room. For basements, attics and larger jobs it is more elaborate.
Ductwork and vents in the area are sealed or covered, and the HVAC system is turned off for the area while the work is under way so the system does not spread spores through the house.
Step 3: Run negative air with HEPA filtration
Inside the containment, the specialist runs one or more air machines fitted with HEPA filters. These pull air out of the contained space through the filter and vent it outside or into a filtered return. Because more air leaves than enters, the room is under slight negative pressure. Air flows in through gaps, rather than leaking out, which keeps spores from escaping into the rest of the house.
HEPA stands for high-efficiency particulate air. A true HEPA filter traps very small particles, including most mold spores. Ask whether the machines are true HEPA and whether they run the entire time the work is going on.
Step 4: Remove what cannot be saved
Mold grows into porous and semi-porous materials. EPA guidance and the industry standard treat these differently from hard surfaces.
Typically removed and discarded:
- Drywall and plaster with mold growth, and wet drywall that has not dried quickly
- Insulation (fiberglass batts and cellulose) that has been wet or has visible growth
- Ceiling tiles
- Carpet and padding
- Particleboard and some paneling
- Mold-affected paper and cardboard
Typically cleaned, if the structure is sound:
- Solid wood framing, studs, joists and subfloor (sanded, scrubbed or media-blasted, then dried)
- Concrete and block (scrubbed and rinsed)
- Metal, glass, tile and plastic
Where the line falls depends on how long the material was wet and how deep the growth goes. A specialist who tells you everything has to go, or one who says nothing needs to go, deserves another question or a second quote.
Removed material is bagged or wrapped inside the containment before it is carried out, so it does not drag spores through the house.
Step 5: Clean the remaining surfaces
After the damaged material is out, the remaining surfaces get cleaned. Commonly:
- HEPA vacuuming of surfaces to pick up loose spores and dust.
- Damp wiping or scrubbing with detergent and water or a cleaner suited to the surface.
- Wire brushing, sanding or media blasting on wood framing where staining or growth is deeper. Media blasting uses soda, dry ice or similar material and can clean framing in a basement or crawl space faster than hand work.
- A second HEPA vacuum after surfaces are dry.
The sequence matters. Dry brushing before vacuuming throws dust. Wiping before drying leaves moisture behind. A careful job works from top to bottom and from the cleanest part of the area to the dirtiest.
Step 6: Dry everything
Drying is where the future of the job is decided. If wood or concrete is left damp, growth resumes.
The specialist may use dehumidifiers, air movers and heat to bring materials to a normal moisture content, and measure with a meter rather than going by feel. In a basement in Kansas City in July, drying takes longer than in January, because the outside air adds moisture. Plan on the drying phase taking several days in humid weather.
Step 7: Clear the work area
When the area is dry and clean, someone checks it. At minimum, that is a visual check: no visible growth, no dust, no musty odor. Sampling may be added as covered on the mold testing page.
The best arrangement is for clearance to be done by a party other than the one that did the work. Agree on the criteria in the contract before work starts. Containment comes down only after the check passes.
Step 8: Rebuild and prevent
Once cleared, rebuilding can begin: new insulation, drywall, trim, flooring and paint. Rebuilding is often a separate trade and sometimes a separate contract. In Kansas City, Missouri, building work generally requires a contractor with the city's license, and may need a permit. Rules differ in Kansas cities and in other Missouri cities, so ask the specialist or your city's permit office what applies.
Prevention is part of the job. That might mean a dehumidifier, a vapor barrier, a bath fan vented outside, regraded soil, a larger gutter, or an added sump pump. The specialist should tell you which of these apply and give you a plan, not a pitch.
Standards and guidance behind the work
Two references do most of the heavy lifting.
ANSI/IICRC S520 is the industry standard for professional mold remediation. It describes conditions (Condition 1 is normal fungal ecology, Condition 2 is settled spores, Condition 3 is actual growth), containment practices, protective equipment, and verification. A company that works from it can show you which parts apply to your job.
EPA guidance on mold in homes, and EPA's document "Mold Remediation in Schools and Commercial Buildings," set out sizes and methods. The size categories in that document (small, medium, large areas) are often used as a starting point for deciding how much containment and protection is needed. EPA's mold pages are at epa.gov/mold.
Neither Missouri nor Kansas has a state license for mold remediation. That means anyone can use the name. Ask which credentials the people doing the work hold (for example from IICRC or ACAC), ask what standard they follow, and check the credentials with the issuing organization.
What you can do yourself
For many small problems, DIY is a reasonable choice. EPA's rule of thumb is that areas smaller than about 10 square feet (roughly a 3 foot by 3 foot patch) can generally be handled by the building occupant, provided you are careful.
DIY is usually fine when:
- The mold covers less than about 10 square feet.
- It is on a hard, non-porous surface (tile, glass, metal, sealed countertop, painted block).
- The cause is known and fixed (a leaky window gasket, a shower that does not dry).
- No one in the home has asthma, serious allergies or a weakened immune system, or those people stay away during the work.
- There is no sign of sewage or floodwater contamination.
If you do it yourself:
- Fix the water problem first.
- Wear an N95 respirator, gloves and eye protection without vent holes.
- Cover nearby items and keep other people and pets out.
- Scrub the surface with detergent and water, rinse, and dry it completely.
- Bag any porous material you remove, in thick plastic, and put it out with the trash.
- Watch the area for the next few weeks. If it comes back, the moisture is still there.
DIY is not a good idea when the mold is on drywall, insulation or carpet and covers a large area, when it is inside walls, when it is in the HVAC system, when contaminated water was involved, or when someone in the home is sensitive. In pre-1980 homes, removing plaster, old flooring or insulation can disturb asbestos or lead paint. Those materials are regulated separately (Missouri DNR and KDHE for asbestos, Missouri DHSS and KDHE for lead), and they change the safe way to do the job.
Reading a remediation quote
A written scope should say, in plain words:
- Where the work will happen and how big the area is.
- What containment and air filtration will be used.
- Which materials will be removed and which will be cleaned.
- How drying will be done and how it will be verified.
- Who fixes the moisture source, and what is and is not included.
- How clearance will be done and by whom.
- Whether rebuild is included.
- What the timeline is, with the caveat that drying depends on weather.
- What happens if the area fails clearance.
Typical costs vary a great deal. Small areas can run from several hundred dollars. Basements, attics and crawl spaces more often run into the thousands, and large or complicated jobs go higher. The specialist quotes after seeing the job. These are general ranges, not this site's prices. Be careful of any quote that is a single number with no scope, and of any offer to apply "fogging" as the whole solution.
Kansas City and drying time
Kansas City has damp, warm summers and cold winters, and clay soil that holds water against foundations, so basements and crawl spaces dry slowly. Plan for the drying phase and the water-source fix to take as much time as the cleanup. See basement mold, attic mold and crawl space mold.
To talk about a job, call the number at the top of the page or use the contact page.
