Most people call for a mold inspection after they smell something musty, see a dark patch on a wall, or finish a repair and find growth behind the drywall. Some call because a home sale is moving forward and the buyer wants to know what is inside the walls. Whatever the reason, a good inspection is mostly detective work about moisture, with mold as the evidence.
This page explains what an inspection covers, what a visit looks like, how to judge whether you need one, and how to avoid the common trap of hiring a company that inspects and then sells you the removal.
What an inspection is supposed to find
Mold needs three things: a food source (wood, drywall paper, dust, insulation backing), the right temperature, and moisture. In a house, the first two are always present. Moisture is the variable. So an inspection is really a search for any place water is getting in, building up, or sitting longer than it should.
A thorough visit looks for four things:
- Visible growth. Where it is, how big the area is, and what material it is on.
- Hidden growth. Behind baseboards, under flooring, inside wall cavities, above ceiling tiles, in the back corners of closets on exterior walls.
- Moisture sources. Plumbing leaks, roof or flashing leaks, window and door leaks, poor grading, failed sump pumps, condensation, bathroom fans that do not vent outside.
- Conditions that will bring it back. High indoor humidity, wet crawl space soil, a clogged gutter that dumps water against the foundation.
If an inspector hands you a report that lists mold but never says where the water came from, you have half an answer.
How moisture mapping works
Moisture mapping is the part of an inspection that separates a careful visit from a quick glance. The inspector uses a few simple tools and a lot of attention.
A moisture meter reads how wet drywall, wood or concrete is, either by pins pushed into the material or by a flat sensor pressed against it. The inspector takes readings along walls and floors and compares wet areas with dry ones, so you can see a pattern: a wet band that follows a pipe, a damp corner under a window, a floor that is wet near the exterior wall and dry in the middle.
A thermal imaging camera shows temperature differences on a surface. Wet materials often look cooler than dry ones, so a camera can point toward a hidden leak. It does not see mold and it does not measure moisture directly, so a good inspector uses it to decide where to check with the meter, not as proof by itself.
A hygrometer measures relative humidity in the air. Readings that stay above about 60 percent for long stretches are a warning sign in any season. Kansas City summers are humid enough that a basement without a dehumidifier can sit in that range for weeks.
A borescope (a small camera on a flexible stick) lets the inspector look through a small hole into a wall cavity or under a floor without tearing anything open.
None of these tools replaces looking and smelling. Many leaks are found by noticing a stained ceiling tile, a swollen baseboard, a bubbled paint line, or a spot where the floor feels slightly soft.
When to call for an inspection
Call when:
- You can smell a musty or earthy odor that does not go away after cleaning and airing out a room.
- You had a water event (pipe burst, roof leak, appliance overflow, flooding) and the area was not dried within a day or two.
- You see staining, bubbling paint, peeling wallpaper, or warped trim and cannot explain why.
- Someone in the home has new or worse allergy or asthma symptoms that seem tied to one room, and a doctor is already involved. (Mold is one possible factor among many. Talk to a doctor about symptoms.)
- You are buying or selling a house and the inspection report mentioned moisture, a damp basement, or past water damage.
- You are a landlord or tenant with a visible problem and need documentation of what is there.
You usually do not need to call when you see a small spot of mold on a hard, non-porous surface such as a tile grout line or a window sill, and you already know the cause (a shower that is not drying, for example). EPA guidance for small areas is that cleaning with detergent and water, and fixing the moisture problem, is often enough. The removal page covers the roughly 10 square foot line in more detail.
What a visit looks like
A typical visit for an average house takes one to three hours. Bigger or more complicated properties take longer.
The inspector starts by asking questions. Where did you notice the problem? When? Has there been any water event, repair, or remodel? Does anyone have health concerns related to the house? How is the house heated, cooled and ventilated?
Then comes a walk-through. The inspector usually starts outside: roof edges, gutters and downspouts, grading around the foundation, window wells, dryer and bathroom vent terminations, and any cracks or staining on the foundation. Many Kansas City basements get water from the outside long before they get mold on the inside, and the lot slope and downspouts are often the cause.
Inside, the inspector goes room by room, usually bottom to top. In the basement, that means checking walls, floor-wall joints, the sump pit, the water heater and furnace area, and any finished walls for signs of moisture. On the main floor, kitchens and bathrooms get close attention. In the attic, the inspector looks at roof sheathing, insulation, and where bath fans and kitchen hoods end. In a crawl space, the focus is soil, vapor barrier, vents and joists.
If something looks like mold, or the readings are strange, the inspector may recommend sampling. Sampling is a separate decision with its own tradeoffs, covered on the mold testing page. Many inspections end with no samples at all, because the cause and the extent are clear without them.
After the visit you should get a written report that includes photos, moisture readings, locations, a plain description of what was found, and what to do about it, in order. Ask for it in writing, and ask what each recommendation costs to skip.
The independent inspector point
This is the most important thing on this page.
Some companies offer a "free" mold inspection and then quote removal on the spot. Others charge a modest fee and credit it toward the work. Neither is automatically dishonest, but the person who finds the problem and the person who profits from the cleanup are the same, and that is a conflict of interest. A problem that could have been solved by fixing a downspout and running a dehumidifier can become a full containment job.
There are two ways to protect yourself:
- Hire an inspector who does not do remediation. The report is not tied to a sale. It tells you what is there and what scope makes sense, and you can take it to two or three remediation companies for comparable quotes.
- If the same company inspects and removes, ask for clearance testing by someone else. After the work is done, a separate party should verify the result before you pay the final balance.
KC Water and Mold connects you with an independent local mold remediation company. The specialist inspects and can remove, which is why the advice above is worth reading. If you want a second opinion before committing to a job, get one. A good company will not mind.
What to ask before you book anyone
Neither Missouri nor Kansas has a state license for mold inspection or mold remediation, so there is no single credential that every inspector must hold. National standards and credentials do exist, including ANSI/IICRC S520 (the industry standard for mold remediation) and credentials such as those offered by IICRC and ACAC. Ask any company which credentials its people hold, ask for the credential names or numbers, and check them with the issuing organization. Also ask:
- What will the report include? Photos, readings, a floor sketch, a written scope?
- Will you do sampling, and if so, why and where, and which lab will you use?
- Do you also do the removal, and if so, how do I get clearance testing from someone independent?
- What happens if you find asbestos or lead paint materials? (In homes built before about 1980, plaster, flooring, insulation and old paint may need separate handling. Asbestos is regulated by the Missouri Department of Natural Resources and by KDHE in Kansas. Lead is handled by Missouri DHSS and KDHE.)
A company that answers these clearly and without hurry is worth more than one that offers the lowest price.
What an inspection may cost
Costs vary by property size, access, and whether sampling is included. A basic visual and moisture inspection of an average home often runs a few hundred dollars, and adding lab samples increases the total. Larger or older homes, crawl spaces with difficult access, and multi-unit buildings cost more. The specialist can give a quote after learning about the property. These are general ranges, not a quote from this site.
Kansas City specifics worth knowing
The metro covers two states, several counties, and housing from the 1900s urban core to subdivisions built in the last few years. Each has its own pattern.
Older homes in places such as Brookside, Waldo, Hyde Park, the Northeast and parts of Independence often have stone or block foundations, original plaster, and basements that have seen decades of water. They commonly have moisture trouble at the foundation wall and the rim joist. Many have crawl spaces under porches or additions that nobody has looked at in years.
Newer suburban homes in Overland Park, Olathe, Lee's Summit and Blue Springs are tighter and better insulated, which is good for energy use and not always good for moisture. Bathroom fans that vent into the attic, poorly sealed ducts, and finished basements with no drainage path are all more common than you would think.
Across the metro, expansive clay soil swells when wet and shrinks when dry. Over the seasons that movement can crack foundations and open paths for water. Humid summers and cold winters add condensation problems in attics and on cold basement walls. You can read more on basement mold, attic mold and crawl space mold.
After the inspection
If it finds a small, easy problem, you may be able to fix the cause and clean the area yourself. Read the removal page first.
If it finds a larger or hidden problem, get a written scope, get at least two quotes, and make sure the plan includes fixing the water source, not just cleaning the surface. Ask who will confirm the result when the work is done.
To request an inspection, call the number at the top of the page or use the contact page.
